How to Install a Tub (Step By Step).
How to Install a Tub (Step By Step).
Blog Article
The article which follows about Tools You Need to Install a New Bathtub is highly compelling. You should give it a look.
Setting up a bathtub isn't specifically brain surgery, however it does need solid plumbing, carpentry, as well as often, tiling abilities. Replacing an old bathtub with a brand-new one is additionally a moderately hard project. If the old tub is easily available, the job can relocate immediately; if you need to open a wall to remove the old bathtub as well as position the brand-new tub, the job is a lot harder. In either case, the project is within a home handyman's skills, although you will need a helper to move out the old tub and set in the new one. Make certain you have qualified yourself for the task and also fit attempting it. Rather than hiring a professional to take over a halfway-completed project, it is far better to think about utilizing one before you begin. Opportunities are you might require an expert plumber to make tube links.
This short article will help you set up a new bath tub in your bathroom if you have currently bought a brand-new tub as well as don't require to transform the arrangement of your previous water system pipes.
Your devices as well as material list ought to consist of the following:
Planning for the Setup
To start with, the sustaining frame provided with the bath needs to be fitted (if needed) according to the manufacturer's directions. Next off, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is essential to make certain that if the faucet comes with a plastic washing machine, it is fitted between the bathroom and the faucets. On a plastic bathroom, it is also practical to fit a supporting plate under the faucets device to avoid strain on the bathtub.
Fit the adaptable tap connectors to the bottom of the two faucets using 2 nuts as well as olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet via the hole in the bath. Make use of the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bathroom. Make sure you utilize every one of the provided washers.
Link the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Link all-time low of the overflow tube in a similar manner.The bathroom must now prepare to be fitted in its last position.
Removing Old Touches
If you need to replace old taps with new ones as a part of your setup, then the first thing you need to do is separate the water supply. After doing so, activate the taps to drain any kind of water remaining in the system. The process of eliminating the existing faucets can be rather troublesome as a result of the limited access that is commonly the instance.
Use a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipelines to the taps. Have a fabric all set for the continuing to be water that will come from the pipelines. As soon as the supply pipes have been eliminated, use the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will require to stop the solitary faucets from transforming throughout this process. Once the taps have been eliminated, the holes in the bath/basin will have to be cleansed of any old sealing compound.
Prior to moving on to fit the brand-new taps, compare the pipeline links on the old faucets to the new faucets. If the old taps are longer than the new faucets, after that a shank adapter is required for the new taps to fit.
Installing the Tub
Utilizing both wooden boards under its feet, position the bath tub in the called for setting. The wood boards are practical in evenly spreading the weight of the tub over the area of the boards rather than focusing all the weight onto four little points.
The next goal is to ensure that the tub is leveled all round. This can be accomplished by inspecting the level and also readjusting the feet on the tub up until the level reviews degree.
To mount taps, fit all-time low of the outermost versatile tap port to the suitable supply pipe by making a compression join; then do the very same for the various other tap.
Turn on the supply of water and check all joints and also new pipework for leakages and tighten them if essential. Fill up the tub as well as additionally inspect the overflow outlet as well as the regular outlet for leaks.
Lastly, repair the bath paneling as defined in the supplier's user's manual. Tiling as well as securing around the tub ought to wait until the bathtub has actually been utilized at least when as this will certainly settle it right into its last placement.
Suitable New Taps
If the tails of the brand-new taps are plastic, then you will certainly require a plastic adapter to prevent damage to the string. One end of the port fits on the plastic tail of the faucet and the other end offers a link to the existing supply pipes.
If you require to fit a monobloc, after that you will certainly need lowering couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next, place the tap in the installing opening in the bath/basin guaranteeing that the washing machines are in area in between the tap and the sink. Secure the faucet in position with the manufacturer provided backnut. When the tap is securely in position, the supply pipes can be attached to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with normal tap connectors. The previous kind must be linked to the faucet finishes initially, tightening up only by hand. The supply pipes can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Bath tub
In the area where the bath satisfies the ceramic tile, it is essential to secure the joins with a silicone rubber caulking. This is essential as the installation can relocate enough to crack a rigid seal, causing the water to pass through the wall in between the bathroom and also the tiling, causing issues with moisture as well as feasible leakages to the ceiling below.
You can choose from a selection of coloured sealers to blend in your components as well as installations. They are marketed in tubes and also cartridges, and are capable of securing spaces approximately a width of 3mm (1/8 inch). If you have a larger space to load, you can load it with twists of soaked paper or soft rope. Bear in mind to constantly fill the tub with water before securing, to permit the motion experienced when the bathtub remains in use. The sealant can split rather very early if you do not consider this motion prior to sealing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are also easily offered on the marketplace. It is suggested to fit the floor tiles making use of water-resistant or waterproof adhesive and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We are very taken with Tools You Need to Install a New Bathtub and I am hoping you enjoyed reading my post. In case you appreciated our article if you please do not forget to pass it around. Many thanks for your time. Don't forget to come by our website back soon.
Schedule Now Report this page